Page10


Latest Update: 21/11/2012
Rear spring problem, see page 11, now resolved.
Sat 09/07/2011, Car passed MOT, tax disc ordered!
Sat 16/07/2011, Road test completed OK.
Nov 2012 Due to a knock on the drivers side rear when turning sharpley, further searching for replacement suspension bush has been ongoing, a new source of rear suspension bush has been found, although not as the origionals, figures in brackets are for origional,  - sourced in USA, body diam 40.2mm (40mm), centre hole 12mm (12mm), centre bush width is 9mm narrower (like Merc ones), bush main body is correct width. It has been possible to skim the body on a lathe from 40.2 to 40mm. Now waiting for a suitable time slot for doing the work
Monday 18th April 2011 - At the age of 11years it had become obvious that the suspension was not working as it should, it turned out that one of the rear springs had broken in 2 places, this was not seen until we removed the rubber gaiters (these are as used on off road/trials motor cycles).
The inboard end bushings of the front suspension arms were very stiff, however sourcing these bushes proved impossible - the 16 replacements items have been turned [very carefully] on a lathe from Polyurethane Rubber "shore A90" material. The front suspension of the car has now been totally refurbished. (see update on page 11 )
The rear suspension has now got new springs (locally sourced) & refurbished shocks from AVO. At this stage we decided we would like to try the redesigned (by RDM Coventry) trailing arms. We never liked the Land Rover style ball joints. A second hand set of Mk3 version arms has been purchased, these are not however suitable for use with the origional Raceline 205 width wheel/tyre combination. We therefore faced further complications, could we modify these to use them with  the 205 width wheel/tyre, we think we can do this, but then could we source the pivot bushes in case we need to replace one at some time, but nobody has the definitive source information. We believe that there could be upto 3 versions of the trailing arms, the origional GTM Mk1, RDM's Mk2 which had been strengthened to become the Mk3. Various source possibilities have been put forward by other GTM Libra owners. Current information from RDM indicates that they are from a Rover 75. We extracted one of the bushes from one of the upper arms to see it in the "flesh". It appears that it is not from the mundane CDTI or 1.8vvc but from the rear suspension of the 4.2 litre Rover 75 V8 or MG ZT260 which is rear wheel drive (only about 900 were produced, will this be the basis of the new MG 6? in 2011, hence the suitability for rear wheel drive Libra's . Rimmer Brothers have them listed but they have no stock & non on order . A bit like trying to find rocking horse sxxt . Meanwhile  modifications to the upper trailing  arms are being carried out, modifying the tubing , then adding 3mm plating top & bottom to give more strength. This  plating adds to the unsprung weight but we think this is acceptable for our road only car.  Below is the bush we extracted  from one of the upper arms. Despite others sayihg that they are retained in place by circlips this one did not have any such retaining system,  it was purely a tight fit - we used a 10 ton hydraulic pulley extractor to remove it, the new bush will need to be put in the freezer for a couple of hours to fit it. Further reseach has gone on today to try and find a bush that we can use and we have decided that the one from Mercedes (several models use this bush) will be useable, with much help from GSF car parts in Sheffield . It is not overall as wide as the "Rover "part, but the body is the same diameter & the same width , the centre hole is 14mm instead of 12mm, spacers and a tube sleeve should solve these problems, (see photos below).
  22 April 2011 - suitable  tube sleeving available at B&Q 14mm OD x 1mm wall thickness giving 12mm ID - needs a little bit of work on the inside wall which is a bit rough, to make it easier fit the 12mm bolt, A 1metre lenght is enough.
 2017 Note: Another correct size bush has now been found,  as fitted to the MGF rear suspension, number to come..........
tip: use plenty of waxol with steel when assembling.
Below are pictures of the process, tools used.


                                                                                                               Close up showing bush being removed downwards
     
The origional bush extracted from the arm,         This is the Mercedes bush we have sourced from GSF car parts.   Mock up "jig" used to see why  205 wide wheel/tyre would  not fit     Width 48mm, Diam 40mm, hole 14mm.b
shown next but one photo below).
Width 57mm, Diam 40mm, hole 12mm.
Possibly Rover V8 or MG ZT260.

                                                                                                                     .


  
View of orional setup.205 wide                                                                                                 wheel/tyre showing "bind" point at front of wheel (on the left looking at the picture).

     
              Another jig view.                                                             Arm & bush.                                                 New tube work shaped & taped in place ready for welding.


     
Parts in preparation for welding                 Arms back from the welders 28/04/2011                       
Saturday 30/04/2011
The bushes had been cooled in the freezer for about 4 hours, then they were refitted into both modified upper trailing arms. They where pressed back into their housings using a 4 inch engineers bench vice.

We then fitted the offside arm into our test rig, the results are very good. See photos above right
We have refitted the hub back onto the car so that we
can turn the car around to get to the back of the end easier. We will have to remove the internal rear trim so that we can get to the mounting bolts.

        n

                                      The clearance between tyre/wheel & upper arm is now evident as the photos show

 

     


       

Removed Mk1 arms & started to fit our Mk4 arms. Our kit of bits to turn the Merc bush into
                                                                                 Libra bush as shown in the next photo.
                                                                                Short sleeve 14mm to 12mm reduction,
                                                                                with brass top hat spacers 25mm diam 4.5mm thick
                                                                               & a small 14mm to 12mm insert.